Essential Plumbing Guide for Installing a Bathtub
Essential Plumbing Guide for Installing a Bathtub
Blog Article
Everybody has got their own piece of advice with regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably difficult job. If the old tub is conveniently accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub as well as position the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have certified on your own for the task and also fit attempting it. Rather than employing a contractor to take over a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a specialist plumber to make tube connections.
This post will certainly help you mount a new bath tub in your bathroom if you have actually already gotten a new bathtub and also do not require to change the plan of your previous water system pipes.
Your tools as well as product list must make up the following:
Planning for the Setup
To start with, the sustaining structure supplied with the bath must be fitted (if required) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the limited access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bath tub in the called for setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bath tub till the level checks out degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the supply of water as well as inspect all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and also check the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub needs to wait up until the bathtub has been utilized at the very least once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Secure the tap in place with the producer provided backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The former type should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall between the bath as well as the tiling, resulting in difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly fill the tub with water prior to securing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture fairly early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Installing A Bathtub? Try leaving feedback further down. We will be pleased to find out your responses about this write up. Hoping that you come back again before long. Kindly set aside a second to share this content if you enjoyed reading it. Bless you for your time. Come back soon.
Immediate response? Click here. Report this page